All-Pro FSL2030L Manuel d'instructions télécharger pdf

Questions?/Questions ? 1-800-334-6871 [email protected]

Instruction Manual/Directives

PACKAGING CONTENTS/CONTENU DU PAQUET

MOUNTING AND WIRING YOUR FIXTURE

WARNING: Risk of electric shock. Disconnect

power at fuse or circuit breaker before installing

or servicing.

NOTE: Fixture can be wall or eave mounted (Fig. 1).

NOTE: Coverplate mounts to recessed mounted

standard junction boxes (Fig. 2). Junction box must be

at least 1-1/2 inch in depth for proper installation for

recessed mount application.

1. Line up the holes on the mounting bracket (B) with

the holes on your junction box. Using either (2) #6

screws or (2) #8 screws (D) (depending on size of

the holes in your junction box), attach the mounting

bracket (B) to your junction box (Fig. 3).

2. Thread ﬁxture wires through coverplate

gasket (C) (Fig. 4).

ITEMS REQUIRED

(Purchase separately)

• Phillips screwdriver

• Outdoor weatherproof silicone caulking

IMPORTANT SAFETY INSTRUCTIONS

When using product, basic precautions should always be followed, including the following:

• Heed all warnings, including below warnings AND those included on product.

• Save these instructions and warnings.

• For outdoor use only.

• cULus LISTED for wet location.

• Disassembling your ﬁxture will void the warranty.

• Your ﬁxture is prewired and preassembled for easy installation.

• Read and follow these instructions.

• Risk of ﬁre/electric shock. If not qualiﬁed, consult an electrician.

• Disconnect power at fuse or circuit breaker before installing or servicing.

CAUTION

• Connect ﬁxture to a 120 volt, 60 Hz power source. Any other connection voids

the warranty.

• Fixture should be installed by persons with experience in household wiring or by a

qualiﬁed electrician. The electrical system, and the method of electrically connecting

the ﬁxture to it, must be in accordance with the National Electrical Code and local

building codes.

• Fixture designed for wall or eave mount to a junction box only. Mount ﬁxture to a

grounded, recessed-mounted standard junction box marked for use in wet locations.

• Do not mount below 5 feet.

SAVE THESE INSTRUCTIONS.

FOR BEST RESULTS

• Install light 10-15 feet above the ground.

• When installing two xtures on one switch, make sure the switch is rated for at least

a 1 A inductive load.

FSL2030LC

(Bronze)

A. Light ﬁxture

L’appareil d’éclairage

ENGLISH

D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in.

(use the size that ﬁts your junction box)

(2) Vis de boite de jonction no6-32 x 19mm (3/4 po)

et (2) vis de boite de jonction no8-32 x 19mm (3/4 po)

(utilisez la taille qui convient à votre boîte de connexion)

E. (3) Wire nuts

(3) Serre-ﬁls

C. Gasket

Joint

G. (2) Decorative screw cover caps

(2) Capuchons décoratifs vissés

F. (2) #8-32 x 1-1/4 in. cover

mounting screws

Vis d’assemblage du couvercle

no8-32 x 32mm (1 1/4 po)

WARNING

B. Mounting bracket

Support de ﬁxation

Wall mount

Eave mount

Round

1-1/2 in.

Octagonal

1-1/2 in.

Junction

box

1 2 3

Résumé du contenu

Page 1 - ENGLISH

Questions?/Questions ? 1-800-334-6871 [email protected] Manual/DirectivesPACKAGING CONTENTS/CONTENU DU PAQUETMOUNTING AN

Page 2 - AVERTISSEMENT

2IMPORTANTES INSTRUCTIONS DE SÉCURITÉDes précautions de base doivent être suivies lors de l’utilisation de ce produit, incluant :• Respectez tous les

Page 3 - GARANTIE LIMITÉE DE 2 ANS

32. Faites passer les ﬁls de la pièce ﬁxe dans le joint du couvercle de protection (C) (Fig. 4).3. Connecter le ﬁl noir de la lampe au ﬁl noir de la

Commentaires sur ces manuels

Pas de commentaire

All-Pro FSL2030L Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Lumières des projecteurs All-Pro FSL2030L. All-Pro FSL2030L Instructions / Assembly Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Lumières des projecteurs All-Pro FSL2030L